A snake made of carbon grows from a tablet of calcium gluconate!
- Put on protective gloves and eyewear.
- Conduct the experiment on the plastic tray and in a well-ventilated area.
- Keep a bowl of water nearby when working with fire.
- Do not allow chemicals to come into contact with the eyes or mouth.
- Keep young children, animals and those not wearing eye protection away from the experimental area.
- Store this experimental set out of reach of children under 12 years of age.
- Clean all equipment after use.
- Make sure that all containers are fully closed and properly stored after use.
- Ensure that all empty containers are disposed of properly.
- Do not use any equipment which has not been supplied with the set or recommended in the instructions for use.
- Do not replace foodstuffs in original container. Dispose of immediately.
- In case of eye contact: Wash out eye with plenty of water, holding eye open if necessary. Seek immediate medical advice.
- If swallowed: Wash out mouth with water, drink some fresh water. Do not induce vomiting. Seek immediate medical advice.
- In case of inhalation: Remove person to fresh air.
- In case of skin contact and burns: Wash affected area with plenty of water for at least 10 minutes.
- In case of doubt, seek medical advice without delay. Take the chemical and its container with you.
- In case of injury always seek medical advice.
- The incorrect use of chemicals can cause injury and damage to health. Only carry out those experiments which are listed in the instructions.
- This experimental set is for use only by children over 12 years.
- Because children’s abilities vary so much, even within age groups, supervising adults should exercise discretion as to which experiments are suitable and safe for them. The instructions should enable supervisors to assess any experiment to establish its suitability for a particular child.
- The supervising adult should discuss the warnings and safety information with the child or children before commencing the experiments. Particular attention should be paid to the safe handling of acids, alkalis and flammable liquids.
- The area surrounding the experiment should be kept clear of any obstructions and away from the storage of food. It should be well lit and ventilated and close to a water supply. A solid table with a heat resistant top should be provided
- Substances in non-reclosable packaging should be used up (completely) during the course of one experiment, i.e. after opening the package.
FAQ and troubleshooting
Apparently, your snake was very impressive! Be sure to wait till everything cools down and the thermosticker turns black. Then you can clean everything up and dispose of the snake with household waste.
The “reptilian” compounds are perfectly safe, so you can dispose of them with ordinary household waste.
Dispose of solid waste together with household garbage.
How does the snake form?
When heated, calcium gluconate (C12H22CaO14) melts and decomposes, producing a lot of carbon dioxide and water vapor. But in order to combust completely, it would require a much greater supply of oxygen than is available to it.
As the oxygen flow to the inner parts of the gluconate tablet is hindered, other complex processes take place at the resulting high temperatures. These processes include the decomposition of gluconate, which produces carbon and water vapor. It is this decomposition, yielding carbon, that gives us our carbon "snake."
In other words, the grey foam resembling a little snake consists of some carbon and other products of calcium gluconate’s decomposition. And this foam forms because a lot of carbon dioxide (as well as some gases that form when the solid fuel burns) and overheated water vapor move vigorously through these products.
Why do we add baking soda (NaHCO3) to our solid fuel?
We do this for two reasons.
First, the solid fuel (also known as urotropine) burns with an almost-colorless flame that is hard to see, which could be dangerous! This is easily fixed with the addition of a sodium compound. Sodium ions, when heated, make the flame the bright orange.
Second, baking soda decomposes when heated, releasing carbon dioxide (CO2) and water vapor:
2NaHCO3 → Na2CO3 + H2O + CO2
Baking soda is added to bread dough to make it rise, and it plays a similar role in this experiment. The carbon dioxide and water vapor that are released make the snake light and airy, which also helps it grow.
What is this "snake" made of?
The "snake" consists mainly of unburnt carbon from the heated calcium gluconate. The carbon is what makes the "snake" black. It also contains sodium carbonate Na2CO3, which forms as the baking soda decomposes in the heat, some calcium carbonate CaCO3 obtained from calcium gluconate, and some CaO produced as the CaCO3 thermally decomposes.
What is solid fuel?
In this case, when we say solid fuel, we mean hexamethylenetetramine or urotropine. This substance is not very complicated, even though its name is. It consists of 6 carbon atoms C, 12 hydrogen atoms H, and 4 nitrogen atoms N. It is written as C6H12N4.
Due to its specific structure, urotropine readily burns in air, releasing mostly water vapor H2O, nitrogen gas N2, and carbon dioxide gas CO2, as well as a lot of heat:
C6H12N4 + 9O2 → 6H2O↑ + 2N2↑ + 6CO2↑
Urotropine burns almost completely and is pretty stable in air. For this reason, it is widely utilized by campers, hobbyists, the military, and relief organizations to heat canned food and military rations.
And, as opposed to wood fires, urotropine does not fear water! Perhaps this is good for campers caught in the rain, but experimenters beware! Don’t use water in an attempt to extinguish urotropine. If the flame is controlled, as in our experiment, just let it burn down completely. But if something goes wrong, cover it with a metallic (fireproof and NOT glass) pot to cut off its oxygen source. Normal fires will die out without oxygen from the air or other sources.
How does the thermosticker work?
This sticker’s main purpose is to react visibly (and reversibly) to heat.
This sticker consists of a yellow picture coated with black dye. When such a sticker is heated (in our case, to 60-70oC), this black dye undergoes some chemical changes and pales, allowing us to see the yellow picture underneath. And when the sticker cools down, the dye reverts to black. This is a reversible process; you can heat and cool this sticker many times.
This is especially helpful when working with heated glassware. More often than not, heated glass doesn’t differ visibly from unheated glass. Attaching such a sticker to the glass before your experiment will ensure that you never make a mistake and grab an overheated object with your bare hands.